Product Description
Transport Handle + D-Ring for inflatable boats
Moulded tow handle specifically designed for the bow of any inflatable boat This Handle provides a double
function: a grip to lift your boat and an anchor point to secure and dock any inflatable dinghy at the same time and
without interfere each other. If you like to leave a mooring rope, or your anchor line, fixed on the bow your boat
from now you have a grip completely free for your hands without worrying anymore about your ropes. This handle has a
specific design to provide simultaneously a hand grip and a D-Ring in the same equipment. This unique handle provides
a 90 grads swinging angle to guarantee a better leverage on the boat and enough space for your hands to grip it and
lift the boat.
This handle consists of two parts:
1. Synthetic tow handle with D-Ring and a 90 degrees free flip movement.
2. PVC pad to be glued on your boat and holding the handle.
Fixed under the bow of any inflatable boat it offers the best pull-performance. To make your boat transportable by a
single person we suggest this handle in combination with our foldable Launching Wheels.
Salt corrosion free product.
Instruction for Glueing
This instruction is created to explain how to attach various equipment to your boat by using our Bengar Montage Kit. The kit includes glue, thinner, duct tape and a brush.
Step 1: Mark and Mask
Hold the equipment you want to attach against the boat and mark the space you will need with a water-based felt marker. Mask this particular space afterwards with the duct tape. Be aware to mask 0,3-0,5 cm more than you actually marked. Clean the marked spaces and and erase the marks.
Step 2: Preparation and Glueing
First of all open the glue with a slotted screwdriver. If the glue is to viscous, please use the enclosed thinner to ensure a perfect consistency. The glue evaporates quickly so you will have to use the thinner a few times, as soon as you realize that the glue is to viscous again. Lay on a first layer of glue on the marked spot on your boat and on the equipment you wish to glue by using the enclosed brush. The best way to do it is by spreading it from in- to the outside so all edges are glue-brushed. Leave it then to dry for about 15 - 20 minutes. The brush should always be kept in the glue or thinner otherwise it will harden. Don't leave the glue or thinner open or uncovered. Close it even during small breaks. Afterwards spread a second layer of glue and remove the duct tape. Lave it to dry for another 5 minutes.
Step 3: Warming and Glueing
Use a hot air gun on the maximum power level to heat up the space where you want to glue on the boat and the equipment for about 30 seconds. Take care of not holding it too long on one spot, otherwise the material could get burned. Our tip: move the hot air gun constantly so it ain’t going to stay longer on one spot than it should. You can also use a hair dryer but you have to pay attention that the spaces you want to glue become warm enough. Be aware of the fact that as soon the booth parts get connected, it will be impossible to reattach it again. After the glueing of the equipment to the boat you should use a little drum or bottle to roll over the glued space to avoid air bubbles and make sure it is connected perfectly.
Step 4: Drying Period
Now you should leave the boat to dry for at least 24 hours so the glue can harden. Leave the glued space smooth and even. If you fold the boat while the drying period it could happen that the equipment hardens in an buckled position.
In Scope of Delivery
- 1 x Handle
- 1 x Glueing Template
- 1 x PVC Pad
Technical Data
| Part Number | 29.02 |
|---|---|
| Barcode | 0611553187393 |
| Made in | Ukraine |
| Weight | 0.23 kg |
| Product Weight | 0.2 kg |
| Delivery time | 3-5 Days |
| Manufacturer | Borika |
| Mounting | Glue |
| Material | Soft & Hard Plastic |
| Color | Black |
