Mid-line Rope Holder (1 hole) for inflatable boats/dinghy, Holding rope Boat Lug

Availability: In stock

Regular Price: €8.00

Special Price: €6.00

Incl. 19% VAT, Excl. shipping
Delivery time 3-5 Days
Shipping - GER : 4,90 €
Lifeline rope holder for inflatables

More Views

  • Lifeline mount for PVC boat
  • Lifeline holder for inflatable boat
  • Rope mount - Life-line - Inflatable boat equipment
  • PVC mount for rope
  • PVC mount for rope - PVC marine equipment
  • rope holder for inflatable dinghy
  • Middle line mount for PVC boat

Videos

Product Description

Middle Rope Lifeline Holder - Life-line Middle Base with 1 hole

This middle line rope holder is used by boat builders to fix a rope or lifeline alongside the boat. A base for rope with a single hole to secure a life-line alongside the boat and provide to the passenger on board a holding point during the navigation.
A holder with double hole is available in the equipment section of our store to be used as start-end rope holder.
Both this accessories can hold a rope up to 14 mm diameter.
This item is developed to be installed to any PVC or Hypalon inflatable boat simply using a specific glue and it comes with a specific template for this purpose.
Of course we provide a complete set to install a whole lifeline alongside the boat including 12 mt. rope, 8 lifeline holder (4 lifeline Middle Mount and 4 lifeline End Mount) and the necessary glue to paste the holders on your inflatable boat.


Instruction for Glueing

This instruction is created to explain how to attach various equipment to your boat by using our Bengar Montage Kit. The kit includes glue, thinner, duct tape and a brush.

Step 1: Mark and Mask

Hold the equipment you want to attach against the boat and mark the space you will need with a water-based felt marker. Mask this particular space afterwards with the duct tape. Be aware to mask 0,3-0,5 cm more than you actually marked. Clean the marked spaces and and erase the marks.

Step 2: Preparation and Glueing

First of all open the glue with a slotted screwdriver. If the glue is to viscous, please use the enclosed thinner to ensure a perfect consistency. The glue evaporates quickly so you will have to use the thinner a few times, as soon as you realize that the glue is to viscous again. Lay on a first layer of glue on the marked spot on your boat and on the equipment you wish to glue by using the enclosed brush. The best way to do it is by spreading it from in- to the outside so all edges are glue-brushed. Leave it then to dry for about 15 - 20 minutes. The brush should always be kept in the glue or thinner otherwise it will harden. Don't leave the glue or thinner open or uncovered. Close it even during small breaks. Afterwards spread a second layer of glue and remove the duct tape. Lave it to dry for another 5 minutes.

Step 3: Warming and Glueing

Use a hot air gun on the maximum power level to heat up the space where you want to glue on the boat and the equipment for about 30 seconds. Take care of not holding it too long on one spot, otherwise the material could get burned. Our tip: move the hot air gun constantly so it ain’t going to stay longer on one spot than it should. You can also use a hair dryer but you have to pay attention that the spaces you want to glue become warm enough. Be aware of the fact that as soon the booth parts get connected, it will be impossible to reattach it again. After the glueing of the equipment to the boat you should use a little drum or bottle to roll over the glued space to avoid air bubbles and make sure it is connected perfectly.

Step 4: Drying Period

Now you should leave the boat to dry for at least 24 hours so the glue can harden. Leave the glued space smooth and even. If you fold the boat while the drying period it could happen that the equipment hardens in an buckled position.


In Scope of Delivery

  • 1 x Rope Holder
  • 1 x Glue Template

Technical Data

Part Number 07.03
Barcode 0611553187331
Made in Ukraine
Weight 0.065 kg
Product Weight 0.05 kg
Delivery time 3-5 Days
Manufacturer Borika
Mounting Glue
Material Soft Plastic
Color Black
  • Mid-line Rope Holder (1 hole) for inflatable boats/dinghy, Holding rope Boat Lug
  • Price: €6.00 - In stock
  • Brand: Borika
  • Color: Black

Please wait...

{{var product.name}} wurde in den Warenkorb gelegt


Continue shopping View cart & checkout Jetzt bezahlen

{{var product.name}} wurde aus dem Warenkorb entfernt


Continue shopping View cart & checkout
Um Ihnen einen optimalen Service auf unserer Webseite zu bieten, verwenden wir Cookies zur Verbesserung der Funktionalität sowie zu Analysezwecken. Durch die weitere Nutzung dieser Webseite erklären Sie sich damit einverstanden. Weitere Details zu den eingesetzten Cookies, ihrer Verwendung und zur Änderung der Cookie-Einstellungen finden Sie in unseren Hinweisen zum Datenschutz.