V-Ring/D-ring for Inflatable boats/dinghy-Tow Ring incl. glue stencil 30.02

Availability: In stock

Regular Price: €20.00

Special Price: €17.00

Incl. 19% VAT, Excl. shipping
Delivery time 3-5 Days
Shipping - GER : 4,90 €
Tow d-ring/ v-ring for inflatable boat with glueing layout

More Views

  • VRing / DRing Oring for inflatable pvc boats
  • V-Ring / D-Ring for pvc inflatable kraft
  • D-Ring - Backside to glue on the boat
  • Tow Handle on a Bengar inflatable boat
  • D-ring for inflatable boat
  • Tow Handle - plan
  • V-Ring-PVC

Videos

Product Description

V-Ring/D-Ring for inflatable boats - Bow anchor point

V-ring, D-ring for inflatable dinghies. Designed to be installed under the bow of any inflatable boat to provide an anchor or docking point.
It consists of two parts:
1. a synthetic tow D-ring.
2. a PVC pad to be glued directly on the boat.
This solution let the D-ring free to swing under the boat to guarantee an extra resilient anchor point.
The specific triangular shape of the PVC pad is ideal for an installation under the bow of the inflatable boat.
Maybe you want to tow your boat: fasten it to a plank or attach an anchor to it....this great anchor/holding/transport point represent the perfect solution.
It´s salt corrosion free, and a glueing template is included.
We offer other products that offer the same performances: D-Rings: 6 different colors to be glued on the inflatable, O-Ring: produced with the same pad system but just a bit smaller than this V-Ring


Instruction for Glueing

This instruction is created to explain how to attach various equipment to your boat by using our Bengar Montage Kit. The kit includes glue, thinner, duct tape and a brush.

Step 1: Mark and Mask

Hold the equipment you want to attach against the boat and mark the space you will need with a water-based felt marker. Mask this particular space afterwards with the duct tape. Be aware to mask 0,3-0,5 cm more than you actually marked. Clean the marked spaces and and erase the marks.

Step 2: Preparation and Glueing

First of all open the glue with a slotted screwdriver. If the glue is to viscous, please use the enclosed thinner to ensure a perfect consistency. The glue evaporates quickly so you will have to use the thinner a few times, as soon as you realize that the glue is to viscous again. Lay on a first layer of glue on the marked spot on your boat and on the equipment you wish to glue by using the enclosed brush. The best way to do it is by spreading it from in- to the outside so all edges are glue-brushed. Leave it then to dry for about 15 - 20 minutes. The brush should always be kept in the glue or thinner otherwise it will harden. Don't leave the glue or thinner open or uncovered. Close it even during small breaks. Afterwards spread a second layer of glue and remove the duct tape. Lave it to dry for another 5 minutes.

Step 3: Warming and Glueing

Use a hot air gun on the maximum power level to heat up the space where you want to glue on the boat and the equipment for about 30 seconds. Take care of not holding it too long on one spot, otherwise the material could get burned. Our tip: move the hot air gun constantly so it ain’t going to stay longer on one spot than it should. You can also use a hair dryer but you have to pay attention that the spaces you want to glue become warm enough. Be aware of the fact that as soon the booth parts get connected, it will be impossible to reattach it again. After the glueing of the equipment to the boat you should use a little drum or bottle to roll over the glued space to avoid air bubbles and make sure it is connected perfectly.

Step 4: Drying Period

Now you should leave the boat to dry for at least 24 hours so the glue can harden. Leave the glued space smooth and even. If you fold the boat while the drying period it could happen that the equipment hardens in an buckled position.


In Scope of Delivery

  • 1 x V-Ring
  • 1 x PVC Pad
  • 1 x Glue Template

Technical Data

Part Number 30.02
Barcode 0611553187409
Made in Ukraine
Weight 0.17 Kg
Product Weight 0.14 Kg
Delivery time 3-5 Days
Manufacturer Borika
Mounting Glue
Material Soft & Hard Plastic
Color Black

Please wait...

{{var product.name}} wurde in den Warenkorb gelegt


Continue shopping View cart & checkout Jetzt bezahlen

{{var product.name}} wurde aus dem Warenkorb entfernt


Continue shopping View cart & checkout
Um Ihnen einen optimalen Service auf unserer Webseite zu bieten, verwenden wir Cookies zur Verbesserung der Funktionalität sowie zu Analysezwecken. Durch die weitere Nutzung dieser Webseite erklären Sie sich damit einverstanden. Weitere Details zu den eingesetzten Cookies, ihrer Verwendung und zur Änderung der Cookie-Einstellungen finden Sie in unseren Hinweisen zum Datenschutz.