2 Rowlocks (pair) black for inflatables boats Oarlock for Inflatable dinghy

Availability: In stock

Regular Price: €25.00

Special Price: €20.00

Incl. 19% VAT, Excl. shipping
Delivery time 3-5 Days
Shipping - GER : 4,90 €
Set mit 2 schwarze Ruderdolle für Schlauchboot

More Views

  • Set mit 2 schwarze Ruderdolle für Schlauchboot
  • Ruderhalter für PVC Luftboote Gummiboot
  • Paddelhalter Grundfläche auf den Boot Außenhaut zur kleben
  • Black pedals for boats
  • Bengars pedals for boats
  • black pedals for boats


Product Description

2 Rowlocks/Oarlocks for inflatable boat

Heavy duty row-locks specific for inflatable boat and dinghy consisting in a PVC base, to be glued on the boat, and an iron steel pin (4cm long and 1cm large) to lock the row. The iron pin has a large PVC screw cap on the top to secure the oar. This oar lock has an inside mechanism that allows the row to swing on a side when not in use, and, in combination with Row-Clips, maintains the row along side the boat during the navigation with engine or transport of the boat itself. 
After years testing these oar-locks on our Bengar inflatable boats we decided to offer them as accessory to improve the functionality on board and to provide the highest safety standard possible. Obviously we can provide all the single parts of these oarlocks like the internal Pin (10mm diameter 40mm long) or the Screw Cap.
This row-locks suit all the "made in Ukraine" oars and here you can find a selection from 80cm to 180cm. 

Instruction for Glueing

This instruction is created to explain how to attach various equipment to your boat by using our Bengar Montage Kit. The kit includes glue, thinner, duct tape and a brush.

Step 1: Mark and Mask

Hold the equipment you want to attach against the boat and mark the space you will need with a water-based felt marker. Mask this particular space afterwards with the duct tape. Be aware to mask 0,3-0,5 cm more than you actually marked. Clean the marked spaces and and erase the marks.

Step 2: Preparation and Glueing

First of all open the glue with a slotted screwdriver. If the glue is to viscous, please use the enclosed thinner to ensure a perfect consistency. The glue evaporates quickly so you will have to use the thinner a few times, as soon as you realize that the glue is to viscous again. Lay on a first layer of glue on the marked spot on your boat and on the equipment you wish to glue by using the enclosed brush. The best way to do it is by spreading it from in- to the outside so all edges are glue-brushed. Leave it then to dry for about 15 - 20 minutes. The brush should always be kept in the glue or thinner otherwise it will harden. Don't leave the glue or thinner open or uncovered. Close it even during small breaks. Afterwards spread a second layer of glue and remove the duct tape. Lave it to dry for another 5 minutes.

Step 3: Warming and Glueing

Use a hot air gun on the maximum power level to heat up the space where you want to glue on the boat and the equipment for about 30 seconds. Take care of not holding it too long on one spot, otherwise the material could get burned. Our tip: move the hot air gun constantly so it ain’t going to stay longer on one spot than it should. You can also use a hair dryer but you have to pay attention that the spaces you want to glue become warm enough. Be aware of the fact that as soon the booth parts get connected, it will be impossible to reattach it again. After the glueing of the equipment to the boat you should use a little drum or bottle to roll over the glued space to avoid air bubbles and make sure it is connected perfectly.

Step 4: Drying Period

Now you should leave the boat to dry for at least 24 hours so the glue can harden. Leave the glued space smooth and even. If you fold the boat while the drying period it could happen that the equipment hardens in an buckled position.

In Scope of Delivery

  • 2 x Rowlocks

Technical Data

Part Number 03.07
Barcode 0608887982510
Made in Ukraine
Weight 0.48 kg
Product Weight 0.45 kg
Delivery time 3-5 Days
Manufacturer Aqua
Mounting Glue
Material Soft Plastic
Color Black

Please wait...

{{var product.name}} wurde in den Warenkorb gelegt

Continue shopping View cart & checkout Jetzt bezahlen

{{var product.name}} wurde aus dem Warenkorb entfernt

Continue shopping View cart & checkout
Um Ihnen einen optimalen Service auf unserer Webseite zu bieten, verwenden wir Cookies zur Verbesserung der Funktionalität sowie zu Analysezwecken. Durch die weitere Nutzung dieser Webseite erklären Sie sich damit einverstanden. Weitere Details zu den eingesetzten Cookies, ihrer Verwendung und zur Änderung der Cookie-Einstellungen finden Sie in unseren Hinweisen zum Datenschutz.