Railblaza QuikPort black round bracket for boat equipment with VHB double sided glue Pad for inflatable's tube installation
This bracket, suitable for all the Railblaza accessories, has been developed especially for inflatable boats.
You can paste the holder on the tube of your inflatabel dinghy with our Glue Kit for PVC inflatabels or with a double adhesive pad by 3M VHB.
You get the best glueing result with our PVC glue kit, ensuring you a resilient installation over the years, moreover the kit works up to 20 QuickPorts.
Alternatively you can use the double-sided VHB adhesive Pad from 3M. Extremely easy to use, we suggest this solution just in case the inflatable boat is not set up and down regularly.
The QuickPort is a smaller version of the RibPort, specifically developed to encumber a narrower surface on the boat's tube. It's cheaper than the RibPort, and due to its smaller area it also has a weaker holding power.
Our Tip: we suggest the QuikPort for all the accessories don't require an extra resilient holding power, like a Mobile Phone holder or Position Light. For a Rod Holder or a Rowlock select the RibPort.
From now the onboard installation of any boat's equipment become easier, you can attach accessories to your Bengar inflatable boat (as well as any inflatable) without a single problem and without having to visit a workshop.
The QuikPort is a star-shaped mount that can hold and lock any RailBlaza accessory. Paste it under the guidance of our glue guide or get a free installation buying a Bengar inflatable boat.
Suitable for almost any surface, such as PVC, Hypalon, fiberglass, epoxy resin and polyethylene used in kayaks production.
The QuickPort has a diameter of 90mm (3.5”)
VHB Pad from 3M - Double sided adhesive stick for QuikPort
Railblaza VHB 3M Self-adhesive double layer pad for QuikPort mount. If you have to fold your inflatable often this Pad could come loose (especially the corners). For a secure and lasting solution we highly recommend to use a professional glue for PVC.
Instruction for Glueing
This instruction is created to explain how to attach various equipment to your boat by using our Bengar Montage Kit. The kit includes glue, thinner, duct tape and a brush.
Step 1: Mark and Mask
Hold the equipment you want to attach against the boat and mark the space you will need with a water-based felt marker. Mask this particular space afterwards with the duct tape. Be aware to mask 0,3-0,5 cm more than you actually marked. Clean the marked spaces and and erase the marks.
Step 2: Preparation and Glueing
First of all open the glue with a slotted screwdriver. If the glue is to viscous, please use the enclosed thinner to ensure a perfect consistency. The glue evaporates quickly so you will have to use the thinner a few times, as soon as you realize that the glue is to viscous again. Lay on a first layer of glue on the marked spot on your boat and on the equipment you wish to glue by using the enclosed brush. The best way to do it is by spreading it from in- to the outside so all edges are glue-brushed. Leave it then to dry for about 15 - 20 minutes. The brush should always be kept in the glue or thinner otherwise it will harden. Don't leave the glue or thinner open or uncovered. Close it even during small breaks. Afterwards spread a second layer of glue and remove the duct tape. Lave it to dry for another 5 minutes.
Step 3: Warming and Glueing
Use a hot air gun on the maximum power level to heat up the space where you want to glue on the boat and the equipment for about 30 seconds. Take care of not holding it too long on one spot, otherwise the material could get burned. Our tip: move the hot air gun constantly so it ain’t going to stay longer on one spot than it should. You can also use a hair dryer but you have to pay attention that the spaces you want to glue become warm enough. Be aware of the fact that as soon the booth parts get connected, it will be impossible to reattach it again. After the glueing of the equipment to the boat you should use a little drum or bottle to roll over the glued space to avoid air bubbles and make sure it is connected perfectly.
Step 4: Drying Period
Now you should leave the boat to dry for at least 24 hours so the glue can harden. Leave the glued space smooth and even. If you fold the boat while the drying period it could happen that the equipment hardens in an buckled position.
You can find here the latest brochure about the whole range of Railblaza products - online browse or download as PDF
In Scope of Delivery
- 1 x Black QuikPort
- 1 x 3M VHB Pad
- 1 x Scrub Pad
- 2 x Alcohol Cleaning Pad
|Made in||New Zealand|
|Delivery time||1-3 Werktage|