Installation of a Fillet Table on an inflatable boat with 2 Ribports
Working Station for Fishing Boat - Fillet Table II
Have you always wanted to clean or gut your fish just after you catch or have a perfect working space for your baits and fishing equipment? Then the Fillet Table from RailBlaza is a must! The large table (525x350mm) is supplied with two platforms with star-shaped adaptors to fit all the Railblaza Mounts. At the front edge, it has two slots for knives and one easy-fit overboard drain that you can open removing the plug, to dispose of various liquids from the table. With 2 Fixed Extensions you can lift the table of 12,5 cm to have a perfect working station on board.
Ribport - Universal Black mount for boat equipment to be glued on inflatable boats.
This mount for Railblaza accessories has been specially developed for inflatable boats. This mount must be pasted
on the tube of your inflatable boat. For this purpose we offer a glue kit that guarantee the best result and it's
enough to paste up to 8 Ribports. Alternatively, you can use the VHB pad from 3M, a double-sided glue tape. We
suggest this solution only when the Ribport is installed and dismantled regularly.
Mounting a rod holder, or any accessory you could need on board, was never so easy: this mount can host any device holder without having to go to a repair shop.
The RIBPort is a star-shaped mount that can hold hold and lock any RailBlaza accessory. Paste it under the guidance of our glue guide or get a free installation buying a Bengar inflatable boat.
Professional 2-components glue for PVC inflatable boats - Kit
This professional adhesives is the same we use to manufacture our inflatable crafts.
The glue is specifically developed for nautical purposes and extremely easy to handle and use. An absolute must for a perfect, durable and resilient reparation of any inflatable PVC boat or the new installation of any boat equipment you could need on your PVC inflatable dinghy.
Starting from now the installation of new fishing and navigation accessories on your inflatable boat, from navigation lights to rod holders or maybe new adjustable seats, is really a simple job.
This adhesives is developed to paste PVC to PVC, PVC to metal and PVC to wood. This user friendly product allows you to install any nautical equipment directly on the boat in a matter of minutes.
PVC Glue 50 ml + PVC Glue Hardener 50ml = 100ml Specific PVC Glue.
Instruction for Glueing
This instruction is created to explain how to attach various equipment to your boat by using our Bengar Montage Kit. The kit includes glue, thinner, duct tape and a brush.
Step 1: Mark and Mask
Hold the equipment you want to attach against the boat and mark the space you will need with a water-based felt marker. Mask this particular space afterwards with the duct tape. Be aware to mask 0,3-0,5 cm more than you actually marked. Clean the marked spaces and and erase the marks.
Step 2: Preparation and Glueing
First of all open the glue with a slotted screwdriver. If the glue is to viscous, please use the enclosed thinner to ensure a perfect consistency. The glue evaporates quickly so you will have to use the thinner a few times, as soon as you realize that the glue is to viscous again. Lay on a first layer of glue on the marked spot on your boat and on the equipment you wish to glue by using the enclosed brush. The best way to do it is by spreading it from in- to the outside so all edges are glue-brushed. Leave it then to dry for about 15 - 20 minutes. The brush should always be kept in the glue or thinner otherwise it will harden. Don't leave the glue or thinner open or uncovered. Close it even during small breaks. Afterwards spread a second layer of glue and remove the duct tape. Lave it to dry for another 5 minutes.
Step 3: Warming and Glueing
Use a hot air gun on the maximum power level to heat up the space where you want to glue on the boat and the equipment for about 30 seconds. Take care of not holding it too long on one spot, otherwise the material could get burned. Our tip: move the hot air gun constantly so it ain’t going to stay longer on one spot than it should. You can also use a hair dryer but you have to pay attention that the spaces you want to glue become warm enough. Be aware of the fact that as soon the booth parts get connected, it will be impossible to reattach it again. After the glueing of the equipment to the boat you should use a little drum or bottle to roll over the glued space to avoid air bubbles and make sure it is connected perfectly.
Step 4: Drying Period
Now you should leave the boat to dry for at least 24 hours so the glue can harden. Leave the glued space smooth and even. If you fold the boat while the drying period it could happen that the equipment hardens in an buckled position.
In Scope of Delivery
- 1 x Fillet Table 2
- 2 x Adjustable Plattform
- 8 x Screws (to fix the platforms to the table)
- 2 x Ribports black
- 1 x Glue
- 1 x Thinner
- 1 x Brush
- 1 x Duct Tape
|Product Weight||2.0 kg|
|Made in||New Zealand|
|Delivery time||3-5 Days|
|Material||Soft & Hard Plastic|