CleatPort RIBMount star system holder with cleat for PVC boat (black) 03-4049-11

Availability: In stock

Regular Price: €32.00

Special Price: €22.95

Incl. 19% VAT, Excl. shipping
Delivery time 3-5 Days
Shipping -GER : 4,90 €
Holder with Bollard for inflatables

More Views

  • Holder with bitt for PVC boats
  • Bitt with star holder for inflatable boat
  • Cleatport dimension
  • halterung mit Klampe Railblaza
  • Bengar PVC boats guide
  • BellyBoot Halterung kleben Railblaza Rutenhalter
  • Railblaza Accessory system for boats


CleatPort RIBMount

Product Description

Railblaza Cleatport Ribmount - black cleat with star mount for inflatable boats.

It’s a simple idea, but very effective. Now your cleat can hold your fishing rod, mobile phone, drink, navigation light, and any accessory from RAILBLAZA that a mount can hold.
This mount was developed especially for inflatable boats and kayaks to provide two functions at the same time.
For a proper and secure installation of this base we suggest a specific PVC glue (as we offer), but you can also use a 3M VHB double layer glue pad (suggested just if you need a temporary installation).
The cleat function that allows you to dock your inflatable is always provided, and it won't interfere with the installed equipment (no matter if it is a rod holder for fishing, a VHF or cell phone holder or even a navigation light).
The CleatPort RIBMount has a star-shaped mount that can hold and lock any RailBlaza accessory without problems. With this mount to install and replace any navigation equipment on your boat is a matter of seconds: just plug it in.
To paste this cleat on the tubes of your inflatable we provide a glue kit with all the instructions you need, or you can have a free installation buying a Bengartastic new boat.

Instruction for Glueing

This instruction is created to explain how to attach various equipment to your boat by using our Bengar Montage Kit. The kit includes glue, thinner, duct tape and a brush.

Step 1: Mark and Mask

Hold the equipment you want to attach against the boat and mark the space you will need with a water-based felt marker. Mask this particular space afterwards with the duct tape. Be aware to mask 0,3-0,5 cm more than you actually marked. Clean the marked spaces and and erase the marks.

Step 2: Preparation and Glueing

First of all open the glue with a slotted screwdriver. If the glue is to viscous, please use the enclosed thinner to ensure a perfect consistency. The glue evaporates quickly so you will have to use the thinner a few times, as soon as you realize that the glue is to viscous again. Lay on a first layer of glue on the marked spot on your boat and on the equipment you wish to glue by using the enclosed brush. The best way to do it is by spreading it from in- to the outside so all edges are glue-brushed. Leave it then to dry for about 15 - 20 minutes. The brush should always be kept in the glue or thinner otherwise it will harden. Don't leave the glue or thinner open or uncovered. Close it even during small breaks. Afterwards spread a second layer of glue and remove the duct tape. Lave it to dry for another 5 minutes.

Step 3: Warming and Glueing

Use a hot air gun on the maximum power level to heat up the space where you want to glue on the boat and the equipment for about 30 seconds. Take care of not holding it too long on one spot, otherwise the material could get burned. Our tip: move the hot air gun constantly so it ain’t going to stay longer on one spot than it should. You can also use a hair dryer but you have to pay attention that the spaces you want to glue become warm enough. Be aware of the fact that as soon the booth parts get connected, it will be impossible to reattach it again. After the glueing of the equipment to the boat you should use a little drum or bottle to roll over the glued space to avoid air bubbles and make sure it is connected perfectly.

Step 4: Drying Period

Now you should leave the boat to dry for at least 24 hours so the glue can harden. Leave the glued space smooth and even. If you fold the boat while the drying period it could happen that the equipment hardens in an buckled position.

  • Broschüre
  • You can find here the latest brochure about the whole range of Railblaza products - online browse or download as PDF

In Scope of Delivery

  • 1 x Black CleatPort RIBMount (Cleat + Mount for Railblaza Accessories)

Technical Data

Part Number 03-4049-11
Lagerort (Intern) N/A
Barcode 9421026832375
Weight 0.27 kg
Product Weight 0.25 kg
Size 160 x 117 x 48,8 mm
Manufacturer Railblaza
Made in New Zealand
Delivery time 3-5 Days
Mounting Glue
Material Soft Plastic
Color Black

Please wait...

{{var}} wurde in den Warenkorb gelegt

Continue shopping View cart & checkout Jetzt bezahlen

{{var}} wurde aus dem Warenkorb entfernt

Continue shopping View cart & checkout
Um Ihnen einen optimalen Service auf unserer Webseite zu bieten, verwenden wir Cookies zur Verbesserung der Funktionalität sowie zu Analysezwecken. Durch die weitere Nutzung dieser Webseite erklären Sie sich damit einverstanden. Weitere Details zu den eingesetzten Cookies, ihrer Verwendung und zur Änderung der Cookie-Einstellungen finden Sie in unseren Hinweisen zum Datenschutz.