Stainless steel O-Ring (175x94mm) and PVC patch to glue on Inflatable Boats - Anchor Point

Availability: In stock

€10.00
Incl. 19% VAT, Excl. shipping
Delivery time 3-5 Days
Shipping - GER : 4,90 €
PVC O-Ring to be installed on PVC inflatable boats

More Views

  • Oring to secure inflatable boat and dinghy
  • D-ring for PVC rib boat - Boat equipment
  • O-Ring- Backside to be glued on PVC boat
  • How to secure an O-ring on your inflatable boat

Videos

Product Description

O-Ring (45 mm) Aqua Black (175x94mm) for inflatable boat and dinghy

Ideal anchor point, that you can install where you need on your inflatable tender, out or inside the boat. This D-Ring is the perfect solution to provide an anchor point to any inflatable craft. The compact size of the O-Ring allow a perfect installation on the round tubes of the inflatable boat letting you free to paste it where you really need. Consisting in a resilient and salt resistant stainless steel O-ring and a PVC pad to keep the O-ring in place but allowing it to swing at the same time. Outside the boat it provide a perfect towing and anchor point, while on board it's a perfect fixing point to secure your stuff on board. This product differs from our usual O-Ring, being designed with a smaller stainless ring and a smaller pad. The elliptical shape of the pad suggest a specific installation on the side of the inflatables, while inside or outside the boat depends only by your specific needs.
Ideal O-Ring for small inflatable boat like: Inflatable Canoes, Inflatable Kayaks and Inflatable Dinghies. When this D-ring doesn't fit your needs we provide other solutions:

-D-ring with PVC pad in 6 different colors and a metal D ring.
--V-ring with large and flexible fitting PVC-pad and a plastic ring.


Instruction for Glueing

This instruction is created to explain how to attach various equipment to your boat by using our Bengar Montage Kit. The kit includes glue, thinner, duct tape and a brush.

Step 1: Mark and Mask

Hold the equipment you want to attach against the boat and mark the space you will need with a water-based felt marker. Mask this particular space afterwards with the duct tape. Be aware to mask 0,3-0,5 cm more than you actually marked. Clean the marked spaces and and erase the marks.

Step 2: Preparation and Glueing

First of all open the glue with a slotted screwdriver. If the glue is to viscous, please use the enclosed thinner to ensure a perfect consistency. The glue evaporates quickly so you will have to use the thinner a few times, as soon as you realize that the glue is to viscous again. Lay on a first layer of glue on the marked spot on your boat and on the equipment you wish to glue by using the enclosed brush. The best way to do it is by spreading it from in- to the outside so all edges are glue-brushed. Leave it then to dry for about 15 - 20 minutes. The brush should always be kept in the glue or thinner otherwise it will harden. Don't leave the glue or thinner open or uncovered. Close it even during small breaks. Afterwards spread a second layer of glue and remove the duct tape. Lave it to dry for another 5 minutes.

Step 3: Warming and Glueing

Use a hot air gun on the maximum power level to heat up the space where you want to glue on the boat and the equipment for about 30 seconds. Take care of not holding it too long on one spot, otherwise the material could get burned. Our tip: move the hot air gun constantly so it ain’t going to stay longer on one spot than it should. You can also use a hair dryer but you have to pay attention that the spaces you want to glue become warm enough. Be aware of the fact that as soon the booth parts get connected, it will be impossible to reattach it again. After the glueing of the equipment to the boat you should use a little drum or bottle to roll over the glued space to avoid air bubbles and make sure it is connected perfectly.

Step 4: Drying Period

Now you should leave the boat to dry for at least 24 hours so the glue can harden. Leave the glued space smooth and even. If you fold the boat while the drying period it could happen that the equipment hardens in an buckled position.


In Scope of Delivery

  • O-Ring

Technical Data

Part Number 02.10
Barcode 0700736969748
Made in Ukraine
Weight 0.1 kg
Product Weight 0.1 kg
Delivery time 3-5 Days
Manufacturer Aqua
Mounting Glue
Material PVC
Color Black
  • Stainless steel O-Ring (175x94mm) and PVC patch to glue on Inflatable Boats - Anchor Point
  • Price: €10.00 - In stock
  • Brand: Aqua
  • Color: Black

Please wait...

{{var product.name}} wurde in den Warenkorb gelegt


Continue shopping View cart & checkout Jetzt bezahlen

{{var product.name}} wurde aus dem Warenkorb entfernt


Continue shopping View cart & checkout
Um Ihnen einen optimalen Service auf unserer Webseite zu bieten, verwenden wir Cookies zur Verbesserung der Funktionalität sowie zu Analysezwecken. Durch die weitere Nutzung dieser Webseite erklären Sie sich damit einverstanden. Weitere Details zu den eingesetzten Cookies, ihrer Verwendung und zur Änderung der Cookie-Einstellungen finden Sie in unseren Hinweisen zum Datenschutz.