Echo Sound Holder for inflatable boat - Installation Video.
Echo Sound Holder for inflatable boat
To secure an Echo Sound on any inflatable fishing boat. We developed this Echo-sound mount especially for fisherman, making it adjustable on the boat and adding on the side 2 PVC rod holders. Naturally we considered a secure place where to stove the necessary battery. To make it demountable and adjustable we use the same solution we use for our adjustable seats, 2 PVC rails to be glued on any fisher boat on witch hanging with our slide-in-supports, the Echo mount. So now....we just wish you merry fishing.
Extra: shelf for battery.
Material: Wood and PVC.
Lower shelf: 17,5 cm long 10 cm wide.
Upper tray surface: 40 cm long 19, 5 cm wide.
Distance of rod-slot openings: 25 cm.
2 x PVC Tracks for Fastening seat bench and Echo Sound mount 40cm
Our PVC tracks are designed to slide into our universal supports to make your equipment on board stable but adjustable. This convenient and light solution is ideal to make your boat more comfortable and light at the same time. Another advantage of this product is that once you fold your boat it won't keep extra space. Extremely light solution to make your accessories on board movable but firmly fixed to your inflatable boat.
For these tracks we use the same PVC of our inflatable vessels Valmex 7318 Mainstream.
2 x Supports for adjustable seat bench - PVC Tracks holder
Once fixed this support to a seat (or to an echo-sound mount) it's enough to let slide into it our PVC tracks in order to fix the desired equipment to any inflatable boat. This system has been proven over the last years, showing off many advantage: your equipment is at the same time stable and adjustable on your inflatable boat. With a weight of only 122g it's a great enhancement to fix a variety of equipment to any inflatable PVC boat. Necessary is a rigid surface where to fix the support with screws to your equipment.
Instruction for Glueing
This instruction is created to explain how to attach various equipment to your boat by using our Bengar Montage Kit. The kit includes glue, thinner, duct tape and a brush.
Step 1: Mark and Mask
Hold the equipment you want to attach against the boat and mark the space you will need with a water-based felt marker. Mask this particular space afterwards with the duct tape. Be aware to mask 0,3-0,5 cm more than you actually marked. Clean the marked spaces and and erase the marks.
Step 2: Preparation and Glueing
First of all open the glue with a slotted screwdriver. If the glue is to viscous, please use the enclosed thinner to ensure a perfect consistency. The glue evaporates quickly so you will have to use the thinner a few times, as soon as you realize that the glue is to viscous again. Lay on a first layer of glue on the marked spot on your boat and on the equipment you wish to glue by using the enclosed brush. The best way to do it is by spreading it from in- to the outside so all edges are glue-brushed. Leave it then to dry for about 15 - 20 minutes. The brush should always be kept in the glue or thinner otherwise it will harden. Don't leave the glue or thinner open or uncovered. Close it even during small breaks. Afterwards spread a second layer of glue and remove the duct tape. Lave it to dry for another 5 minutes.
Step 3: Warming and Glueing
Use a hot air gun on the maximum power level to heat up the space where you want to glue on the boat and the equipment for about 30 seconds. Take care of not holding it too long on one spot, otherwise the material could get burned. Our tip: move the hot air gun constantly so it ain’t going to stay longer on one spot than it should. You can also use a hair dryer but you have to pay attention that the spaces you want to glue become warm enough. Be aware of the fact that as soon the booth parts get connected, it will be impossible to reattach it again. After the glueing of the equipment to the boat you should use a little drum or bottle to roll over the glued space to avoid air bubbles and make sure it is connected perfectly.
Step 4: Drying Period
Now you should leave the boat to dry for at least 24 hours so the glue can harden. Leave the glued space smooth and even. If you fold the boat while the drying period it could happen that the equipment hardens in an buckled position.
In scope of delivery
- 1 x Echo Sound Holder with 2 rod holders
- 2 x 40 cm tracks in various colors
- 2 x track holder (already fixed to the Echo Sound Holder)
|Size||40 cm x 19, 5 cm|
|Delivery time||3-5 Days|
|Product Weight||1.87 kg|