Front cover/canopy for inflatables boats / dinghies - 145-170cm wide L

Availability: In stock

Incl. 19% VAT, Excl. shipping
Delivery time 1-3 Werktage
Shipping - GER : 4,90 €

More Views

  • Bow cover for inflatables boats
  • Bow canopy for PVC dinghy
  • Bow canopy for inflatable dinghy
  • Bow tent  for inflatables boats and dinghy
  • PVC Equipment for inflatable boat
  • Bow front cover canopy tent for inflatables boats dinghy
  • Front water protection for boat
  • Bengar Inflatable boat accessory
  • PVC Accessory for bats
  • Bugabdeckung für Schlauchboote
  • Schlauchboot Zubehör Bugabdeckung
  • Aufblasbarer Bugabdeckung für Schlauchboote
  • Knobs for buckles - marine equipment
  • maßzeichnung bugabdeckung large


Product Description

Large Bow Canopy for Dinghy and Inflatable Boat 145-170cm broad

A canopy to apply to any inflatable boat's bow to protect the on board passengers from waves, water and wind during the navigation. Useful to protect from sun and water the bags, equipment and all the stuff needed for your adventures on the water. This canopy comes in different measures to fit any inflatable boat from 2 mt up to 4 mt, and it´s composed of two parts: an inflatable 4 points arch structure that provide rigidity, and a robust waterproof tent that covers the inflatable structure. The inflatable arch provides a great back seat for on board passengers, while the tent improves the speed of the boat thanks to a better vessel's aerodynamic. The PVC inflatable structure hold in position the waterproof tent thanks to several velcro straps on the top of it. The inflatable arch and the canopy are both provided of fast buckle with straps to be anchored to the bow of the boat trough 7 knobs (provided with the Product). Using a dinghy for fishing or just for pleasure can be much more comfortable with this inflatable cover, providing a sun/water protected area on board. We designed this inflatable front tent to improve the on board comfort and the performances of our inflatable dinghies.
The Canopies are available in 4 different measures to fit inflatable boats 115cm - 190cm broad.

For inflatable Boats 115-135 cm wide
For inflatable Boats 135-145 cm wide
For inflatable Boats 145-170 cm wide
For inflatable Boats 170-190 cm wide

Instruction for Glueing

This instruction is created to explain how to attach various equipment to your boat by using our Bengar Montage Kit. The kit includes glue, thinner, duct tape and a brush.

Step 1: Mark and Mask

Hold the equipment you want to attach against the boat and mark the space you will need with a water-based felt marker. Mask this particular space afterwards with the duct tape. Be aware to mask 0,3-0,5 cm more than you actually marked. Clean the marked spaces and and erase the marks.

Step 2: Preparation and Glueing

First of all open the glue with a slotted screwdriver. If the glue is to viscous, please use the enclosed thinner to ensure a perfect consistency. The glue evaporates quickly so you will have to use the thinner a few times, as soon as you realize that the glue is to viscous again. Lay on a first layer of glue on the marked spot on your boat and on the equipment you wish to glue by using the enclosed brush. The best way to do it is by spreading it from in- to the outside so all edges are glue-brushed. Leave it then to dry for about 15 - 20 minutes. The brush should always be kept in the glue or thinner otherwise it will harden. Don't leave the glue or thinner open or uncovered. Close it even during small breaks. Afterwards spread a second layer of glue and remove the duct tape. Lave it to dry for another 5 minutes.

Step 3: Warming and Glueing

Use a hot air gun on the maximum power level to heat up the space where you want to glue on the boat and the equipment for about 30 seconds. Take care of not holding it too long on one spot, otherwise the material could get burned. Our tip: move the hot air gun constantly so it ain’t going to stay longer on one spot than it should. You can also use a hair dryer but you have to pay attention that the spaces you want to glue become warm enough. Be aware of the fact that as soon the booth parts get connected, it will be impossible to reattach it again. After the glueing of the equipment to the boat you should use a little drum or bottle to roll over the glued space to avoid air bubbles and make sure it is connected perfectly.

Step 4: Drying Period

Now you should leave the boat to dry for at least 24 hours so the glue can harden. Leave the glued space smooth and even. If you fold the boat while the drying period it could happen that the equipment hardens in an buckled position.

Size and Dimensions

Size S M L XL
Bengar Inflatable Model L-240, L-280 L-280U N-320, L320 N-360, B-360
Fits boat broad 115-135 cm 135-145 cm 145-170 cm 170-190 cm
Canopy broad 164 cm 171 cm 160 cm 197 cm
Canopy long 88 cm 90 cm 87 cm 111 cm
Inflatable Arch broad 130 cm 120 cm 104 cm  132 cm
Inflatable Arch high 45 cm  47 cm 45 cm 45 cm 
Inflatable Arch long 60 cm  60 cm  60 cm  80 cm 

In Scope of Delivery

  • 1 x Inflatable Bow Arch - Structure
  • 1 x Bow Canopy
  • 7 x Buckles
  • 7 x Knobs/Hooks

Technical Data

Part Number BZ-1L
Barcode 0611553185658
Size Nein
Delivery time 1-3 Werktage
Weight 2.77 Kg
Product Weight 2.34 Kg
Made in Ukraine
Manufacturer Bengar
Mounting Glue
Material 100% Polyester
Color Black

Please wait...

{{var}} wurde in den Warenkorb gelegt

Continue shopping View cart & checkout Jetzt bezahlen

{{var}} wurde aus dem Warenkorb entfernt

Continue shopping View cart & checkout
Um Ihnen einen optimalen Service auf unserer Webseite zu bieten, verwenden wir Cookies zur Verbesserung der Funktionalität sowie zu Analysezwecken. Durch die weitere Nutzung dieser Webseite erklären Sie sich damit einverstanden. Weitere Details zu den eingesetzten Cookies, ihrer Verwendung und zur Änderung der Cookie-Einstellungen finden Sie in unseren Hinweisen zum Datenschutz.